na3D
400 products
-
Add to FavouritesSet 4 x Driver TMC2130 SPI Cable
Set four pieces of TMC 2130 stepper drivers with SPI bus output, including connection cable.
Sold out
38,65 €
-
Add to FavouritesBall bearing 626ZZ
Single -row ball bearing 6W6 2Z suitable for high and extremely high temperatures. Size 6x19x6 mm. 626 ZZ (the product can be ordered for 1 piece, photographs are only illustrative.)
Sold out
0,67 €
-
Add to FavouritesBall bearing 628ZZ
Ball bearing 628ZZ, 8x24x8 mm. (The product can be ordered after 1 piece, the photo is only illustrative.)
Sold out
1,02 €
-
Add to FavouritesLM16ULU linear bearing
Extended linear bearing suitable for assembly into a wide range of printers. Suitable for guide bars with a diameter of 16 mm. (The product can be ordered after 1 pc.)
Sold out
7 €
-
Add to FavouritesLM25UU linear bearing
Extended linear bearing suitable for assembly into a wide range of printers. Suitable for guide rods with a diameter of 25 mm. (The product can be ordered after 1 pc.)
Sold out
9,81 €
-
Add to FavouritesGT2 pulley - black anodex
Pulley for engine deployment or rod with the possibility of securing two screws (worms). Black GT2 pulley with 20 teeth on engine shaft 5 mm (inner pulley hole 5 mm). (The product can be ordered after 1 piece, the photo is only illustrative.)
Sold out
2,07 €
-
Add to FavouritesInduction proximity sensor LJ18A3-8-Z/BX
Sensor 8 mm detection distance. The sensor indicates the detection of the object by the appearance of the low state at the output and activation of the red LED. The sensor is equipped with a cable with a length of about 1m and a nut for easy assembly. The sensor is equipped with a cable with a length of about 1 m and a nut for easy assembly. The sensor tightness class is IP67. The power range...
Sold out
8,76 €
-
Add to FavouritesSet of travel rods Rebelix x2
Set of hardened travel rods for assembling 3D Rebelix X2 printers.
Sold out
17,55 €
-
Add to FavouritesPower Panic v0.4
Connector before the source for monitoring a decrease in network connection. Supports 12 and 24 V.
Sold out
17,55 €
-
Add to FavouritesPrusa MMU Control V2
Control board for multimatcher printing. Prusa mm Control
Sold out
35,13 €
-
Add to FavouritesCR10 heatblock cube
Replacement aluminum cube (Heatblock) for extruders on Creality printers.
Sold out
2,78 €
-
Add to FavouritesU604 - bearing with groove for filament pressure
Bearing with groove for filament pressure. Most often used in the MK8 extruder. (The product can be ordered after 1 piece, the photo is only illustrative.)
Sold out
1,02 €
-
Add to FavouritesMagnetic print pad with magnetic sticker 220 x 220 mm
Magnetic printing pad with dimensions of 220 x 220 mm for better adhesion of prints. It is a two-part set, where a detachable magnetic pad guarantees easier removal of the printed products.
Sold out
8,76 €
-
Add to FavouritesMotor connector - dual z
Motor connector - suitable for dual Z. Parallel connection of 2 engines to one output of the control board.
Sold out
1,72 €
-
Add to FavouritesFilament welding
Filament welding product available in two dimensions. Dimensions 1.75 mm and 3.0 mm. The welding product is used to connect the ends of the strings to make the most of the coil content.
Sold out
from 10,51 €