na3D
508 products
-
Add to FavouritesConventor for thermistor Pt100
External temperature measurement module with ceramic thermistor PT100. The board allows you to reinforce the output of the PT100 sensor for connecting to the analagous control plate input. The plate amplifies the PT100 voltage to the level for more accurate temperature sensing. We recommend selecting the definition "20" in Marlin.
Sold out
6,66 €
-
Add to FavouritesPrint plate clip
A swivel metal clip for easy glass attachment to the printing mat. Recommended to a thickness of 6mm. Minimalist attachment of the print pad, does not detract from the printing area, like other clips. (The product can be ordered after 1 piece, the photo is only illustrative.)
Sold out
0,97 €
-
Add to FavouritesMK8 Extruder 1.75/0.4 mm
Complete extruder head MK8 for Anet, Geet, Tronxy and more. (The head is without the engine cable.)
Sold out
20,05 €
-
Add to FavouritesMk8 aluminum cube
Spare heating block for MK8 extruders. The cube has a worm for heating body insurance. The cube is most often used in Geet, Anet, Creality, etc.
Sold out
1,64 €
-
Add to FavouritesBall bearing 6000 Rs
Uncharged single-row radial ball bearing with steel cage. (The product can be ordered after 1 piece, the photo is only illustrative.)
Sold out
1,17 €
-
Add to FavouritesSet 4 x Driver TMC2130 SPI Cable
Set four pieces of TMC 2130 stepper drivers with SPI bus output, including connection cable.
Sold out
36,78 €
-
Add to FavouritesLM16ULU linear bearing
Extended linear bearing suitable for assembly into a wide range of printers. Suitable for guide bars with a diameter of 16 mm. (The product can be ordered after 1 pc.)
Sold out
6,66 €
-
Add to FavouritesLM25UU linear bearing
Extended linear bearing suitable for assembly into a wide range of printers. Suitable for guide rods with a diameter of 25 mm. (The product can be ordered after 1 pc.)
Sold out
9,34 €
-
Add to Favourites3DLAC plus
A non -pressure variant of the popular 3DLAC spray. Volume 100 ml. The sprayer is sufficient for more than 200 spraying of the pad (the advantage is that it is not necessary to re -apply before each print with a properly applied first layer). In case of dissatisfaction we offer a refund within 30 days.
Sold out
7 €
-
Add to FavouritesGT2 pulley - black anodex
Pulley for engine deployment or rod with the possibility of securing two screws (worms). Black GT2 pulley with 20 teeth on engine shaft 5 mm (inner pulley hole 5 mm). (The product can be ordered after 1 piece, the photo is only illustrative.)
Sold out
1,97 €
-
Add to FavouritesRAMPS 1.6+
Reprap Arduino Mega Pololu Shield 1.6 Plus The latest version of the popular RamPs album. Mosfets were replaced by more powerful ones and are under a large cooler. Also, the terminal block has been upgraded and now you do not have to change anything. In addition, double connectors.
Sold out
11,68 €
-
Add to FavouritesSet of travel rods Rebelix x2
Set of hardened travel rods for assembling 3D Rebelix X2 printers.
Sold out
16,70 €
-
Add to FavouritesPower Panic v0.4
Connector before the source for monitoring a decrease in network connection. Supports 12 and 24 V.
Sold out
16,70 €
-
Add to FavouritesPrusa MMU Control V2
Control board for multimatcher printing. Prusa mm Control
Sold out
33,44 €
-
Add to FavouritesCR10 heatblock cube
Replacement aluminum cube (Heatblock) for extruders on Creality printers.
Sold out
2,64 €